Re: I Need A Shrink !
 

Thanks fellas

Thats a good piece of advice about heating the tube to make it stronger....I never thought of that. I guess I got lucky with the Cetol...to be honest I did not put much thought into which teak product to get. The guy at West Marine mentioned the article in Power Boats so thats why I went with it. I put 3 coats of it on the teak..did not sand in between coats.

As far as when to cut the holes thats kinda like six one half a dozed or the other. I dot see any real advantage to doing it before paint other then it may save a tiny bit of fairing and paint. It's just the way I do it. If I had a real large area to cut out I may do it prior to paint. Thanks again...more photos to come soon.

strick

Re: I Need A Shrink !
 

A couple more quick photos

14 gallon fresh water bladder tank

http://www.casdvm.com/photos/25%232internet/500.JPG

Set in place along with a 1500 GPH bilge pump.


http://www.casdvm.com/photos/25%232internet/501.JPG


making a battery platform


http://www.casdvm.com/photos/25%232internet/502.JPG


This weekend I'm shooting to get the tower mounted as well as start the plumbing for the live well and dead fish hold.

strick

Re: I Need A Shrink !
 

:D

Nice work indeed!

Re: I Need A Shrink !
 

Seems like there is always something going on that keeps me from working on the boat. We have company coming over this evening so I better post now.

Backing plates cut for the radar arch and cleats

http://www.casdvm.com/photos/25%232internet/503.JPG

table for two

http://www.casdvm.com/photos/25%232internet/504.JPG


Fuel/ water fills and vent on the port side. There is another fuel fill on the starboard side

http://www.casdvm.com/photos/25%232internet/508.JPG


Most of the wiring is going to run under the gunnel cap on this boat but I wanted to put in a chase tube so I could easily run whatever after the deck is sealed up. The boat had a hole cut inside the cabin beneath the helm for the steering cable. I ran some 3" abs under the deck to the engine compartment from this hole. I had to put in a round access deck plate so I could do the plumbing. This is a just in case chase tube. A couple shots showing this:


http://www.casdvm.com/photos/25%232internet/510.JPG

http://www.casdvm.com/photos/25%232internet/512.JPG



Installing thru hull fittings these are for the two bilge pumps


http://www.casdvm.com/photos/25%232internet/513.JPG

http://www.casdvm.com/photos/25%232internet/514.JPG

http://www.casdvm.com/photos/25%232internet/515.JPG

http://www.casdvm.com/photos/25%232internet/516.JPG


Installing thru hulls for the live well overflow and the end of day drain for the dead fish box and live well. These are 1.5" thru hulls:

http://www.casdvm.com/photos/25%232internet/517.JPG

Epoxy is used to seal the wood

http://www.casdvm.com/photos/25%232internet/519.JPG


Lots of 5200 on these


http://www.casdvm.com/photos/25%232internet/520.JPG

http://www.casdvm.com/photos/25%232internet/521.JPG

http://www.casdvm.com/photos/25%232internet/522.JPG


Bronze valves on the transom. It's going to be fun trying to avoid the manifolds when turning these on and off but there was no other place on the boat that I could mount them. Just going to have to be careful I guess.

http://www.casdvm.com/photos/25%232internet/523.JPG

http://www.casdvm.com/photos/25%232internet/524.JPG

http://www.casdvm.com/photos/25%232internet/525.JPG


Finally I was able to get the radar arch mounted yesterday. Thanks to Bill and Butch for coming over and helping me with that project.

http://www.casdvm.com/photos/25%232internet/505.JPG

http://www.casdvm.com/photos/25%232internet/506.JPG

http://www.casdvm.com/photos/25%232internet/507.JPG

http://www.casdvm.com/photos/25%232internet/509.JPG


Backing plates for the radar arch

http://www.casdvm.com/photos/25%232internet/518.JPG



strick

Re: I Need A Shrink !
 

She is looking HOT!!!!! :cool:

Re: I Need A Shrink !
 

That's one fantastic-looking boat!

Re: I Need A Shrink !
 

Awesome!! On the drain valves...maybe a hole at the end of the handle for a 1/4" SS rod?? Kinda like a safety shower pull.

Re: I Need A Shrink !
 

Thanks for all the cheering fellas.

I've been doing lots of plumbing over the course of the past several days. Cutting lots of holes in various places on the boat. A few pictures of what has been done.

shot showing the bait tank pump and live well overflow

http://www.casdvm.com/photos/25%232internet/526.JPG

Raw water pump mounted in engine compartment

http://www.casdvm.com/photos/25%232internet/527.JPG

There are going to be three Brass drains in the cabin floor

http://www.casdvm.com/photos/25%232internet/528.JPG

Fresh water pump mounted on the stringer port side in the cabin

http://www.casdvm.com/photos/25%232internet/529.JPG

Fittings for the bait tank and fresh water nipple

http://www.casdvm.com/photos/25%232internet/530.JPG

Getting the seat boxes ready

http://www.casdvm.com/photos/25%232internet/531.JPG

Trial fitting the seat boxes. I need to put a little more foam on the one on the starboard side.

http://www.casdvm.com/photos/25%232internet/532.JPG

http://www.casdvm.com/photos/25%232internet/533.JPG

http://www.casdvm.com/photos/25%232internet/534.JPG


Inspection plates

http://www.casdvm.com/photos/25%232internet/535.JPG


Backing cleats for the seat boxes. This is PVC board from the local hardware store.


http://www.casdvm.com/photos/25%232internet/536.JPG

http://www.casdvm.com/photos/25%232internet/537.JPG


On to the teak swim platform...one of the pieces was missing so I cut a new one

http://www.casdvm.com/photos/25%232internet/538.JPG


First coat of Cetol

http://www.casdvm.com/photos/25%232internet/539.JPG


Alaska

http://www.casdvm.com/photos/25%232internet/540.JPG

http://www.casdvm.com/photos/25%232internet/541.JPG


strick

Re: I Need A Shrink !
 

As always, beautiful work and terrific planning. She is blossoming before our eyes.

The last shot of the plane is quite something. Isn't that an old Beaver model plane, so often used by the bush pilots in the northern outback?

(I am probably going to catch H--l for the wording, but it is all correct in its context.)

Re: I Need A Shrink !
 

Yes its a Beaver. One tough plane :cool:

strick