Classic SeaCraft Community

Classic SeaCraft Community (http://www.classicseacraft.com/community/index.php)
-   SeaCraft Photos (http://www.classicseacraft.com/community/forumdisplay.php?f=8)
-   -   My first (http://www.classicseacraft.com/community/showthread.php?t=15866)

CHANCE1234 12-07-2005 09:49 PM

Re: My first
 
Yup, supposed to snow again on friday. Could make for an interesting drive home from the south shore get together. [img]/images/graemlins/smirk.gif[/img]

EBEACH 12-08-2005 02:03 AM

Re: My first
 
I replaced my anchor panel, and I HAD to remove the cap. I assume the CC would be the same. You could probably cut yours out, and then make the new one just an inch or so short along the top and then fit in a narrow strip along the top.

Jim

Miles Offshore 12-08-2005 04:43 PM

Re: My first
 
how high does the anchor locker piece go????

CHANCE1234 12-08-2005 04:48 PM

Re: My first
 
Hey craig, it doesen't go all the way to the cap but pretty close, probably about and inch or 2 tops. I am just leaving to go check, i'll let you know later tongiht.

Elijah

cSickNick 12-08-2005 05:00 PM

Re: My first
 
I like the dog house set up. In the NE, it is a practical setup. Nice job. [img]/images/graemlins/smile.gif[/img]

It also reminds me when i was a kid, i spent alot more time in the "old doghouse" hanging on the kitchen wall than my siblings.

I hope somebody knows what i am talking about .... if not, ignore ... as usual ... [img]/images/graemlins/smirk.gif[/img]

CHANCE1234 12-08-2005 07:33 PM

Re: My first
 
Alright Craig, I took it one step further. Instead of checking the height, I took the whole thing out, almost in one piece. So if you or anyone else wants a template let me know and I will make something up and send it out. Here are some pictures.
http://i19.photobucket.com/albums/b1...1234/p4046.jpg
http://i19.photobucket.com/albums/b1...1234/p4047.jpg
http://i19.photobucket.com/albums/b1...1234/p4048.jpg
http://i19.photobucket.com/albums/b1...1234/p4049.jpg
http://i19.photobucket.com/albums/b1...1234/p4050.jpg

Tools needed for this project: hammer, chistle, vice grips with razor blade (couldn't find my utility knife), and a few punches to loosen her up. Total time 40 minutes.

Miles Offshore 12-08-2005 07:38 PM

Re: My first
 
pretty work there Elijah ! if you wouldnt mind sending me a pattern i would be greatly appreciative. my address is

Craig Miles
1845 Castleton Ct.
Va. Beach, Va. 23454

Just lemme know if i owe you any shipping and i will shoot it right back- thanx- craig [img]/images/graemlins/smile.gif[/img]

CHANCE1234 12-08-2005 08:54 PM

Re: My first
 
You bet, I should have it in the mail by the end of next week. It did go pretty much all the way to the top of the cap so you may have a problem getting a new one in unless you cut it a little short. I guess you could always make it to size then cut the top after if needed.

SC204 12-09-2005 09:41 AM

Re: My first
 
What kind of boat is the yellow one behind yours?

CHANCE1234 12-09-2005 09:54 AM

Re: My first
 
Thats a 20 SF, Seacraft, I don't believe it is for sale, if thats what your looking for.


All times are GMT -4. The time now is 12:32 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
All original content © 2003-2013 ClassicSeacraft