![]() |
Hammers 1971 20 CC
Please post your questions or coments about Hammers 20.
|
Re: Hammers 1971 20 CC
i throught awi grip wasn't a paint that you could use on bottoms? i wanted to use it on a 18 outrage i had but was told its not for bottoms.
[ September 05, 2002, 03:20 PM: Message edited by: fylfisher ] |
Re: Hammers 1971 20 CC
Flyfisher you are correct. Hammer leaves his boat on a trailer so he felt it would be ok. If you leave the boat in the water for an extended amount of time the Awl-Grip may blister.
Re-Gelcoating the bottom, as Fellow-Ship did, is a better solution if you plan on leaving the hull in the water for a while at a time |
Re: Hammers 1971 20 CC
well he did a beautiful job. the only thing i think i would have done different, sense he did redue the transum. would be to close it complety in and use a bracket. but that is a personl choise. how do you guy feel about a bracket on a 20ft seacraft?
[ September 06, 2002, 12:02 PM: Message edited by: flyfisher ] |
Re: Hammers 1971 20 CC
I call AwlGrip and talked to the Teck about this and he assured me that two or three nights a month is NOTHING to worry about. He did say that you would not want to leave it in the water for a week or two.
|
Re: Hammers 1971 20 CC
thanks guys . sorry about the post here on the bracket. i just found the topic in the forum. i feel better now knowing that what i was told was right. mine some times sends one or more weeks in the water. i some time don't turst the boat suppie co. around here were i live. i have a 20ft mako now. but in a little less then 2 years i'll be retiring and moving to the coast. i reelly want a 23 or 25ft seacraft when i do. i love a friends 23 inboard. but i feel better about outboards because i have rebuilt and helped to repair so my i know what to do if they hecup. inboards still loss me.
|
Re: Hammers 1971 20 CC
Fairing??? Hammer how did you do such a great job fairing the transom? please post any techniques, products, and tools that helped you achieve such a smooth transom.
|
Re: Hammers 1971 20 CC
HAMMER YOU 20 LOOKS GREAT,I got my eye on a 20 that i hope i can get for the right price, If I do get it im going to raise the transom to 25 and hang my 225 that I have on my 23 now.My concern is the weight, It might not self bail.
|
Re: Hammers 1971 20 CC
Reel-Smoker,
You might want to talk to Mike (wildfire) about hanging that engine on a 20'. I think he told me that he put a 235 on the back of his 20'CC - but he raised the floor 2", which could make a bit of difference when it comes to self bailing. I think I'd raise the floor a few inches even if I was going to put a 5hp engine on, as just standing in the back without the plugs in yields wet toes. Hope you can get that 20' you are after/ mark |
Re: Hammers 1971 20 CC
Reel-Smoker,
You might want to talk to Mike (wildfire) about hanging that engine on a 20'. I think he told me that he put a 235 on the back of his 20'CC - but he raised the floor 2", which could make a bit of difference when it comes to self bailing. I think I'd raise the floor a few inches even if I was going to put a 5hp engine on, as just standing in the back without the plugs in yields wet toes. Hope you can get that 20' you are after/ mark |
Re: Hammers 1971 20 CC
Mark thanks for the advice.Im sorry was it you that took a 20 to Mike at Wildfire? If Im able to buy it im going to see if I can run the scuppers straight back like he did to my 23, but now that I think of it it probably wont work they'll be under water the Rabud scuppers will plug it up but I dont like the idea of them being under water at all times,your right raising the floor might be the solution or going with a lighter motor.Thanks again.
|
Re: Hammers 1971 20 CC
Hammer, is the console original equipment? If not where can I locate one similar. Looking at a '79 Master Angler that needs a little renovation: fuel tank, transom etc. You did a great job! Thanks
|
All times are GMT -4. The time now is 03:06 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
All original content © 2003-2013 ClassicSeacraft