Classic SeaCraft Community  

Go Back   Classic SeaCraft Community > Search Forums
Reload this Page Search Results
FAQ Community Calendar Today's Posts Search

Notices

Showing results 1 to 11 of 11
Search took 0.00 seconds. Search: Posts Made By: Captdj
Forum: Recovered Threads 12-17-2016, 05:27 AM
Replies: 3
Views: 60
Posted By Captdj
I have a the 23 center console and have the same...

I have a the 23 center console and have the same issue. After it rains I can take off the pie plate in front of the console and there is water down there. Its just seems like the boat sits so flat in...
Forum: Recovered Threads 06-17-2016, 12:18 PM
Replies: 8
Views: 65
Posted By Captdj
Ok so I switched the prop over to the 18.5 my...

Ok so I switched the prop over to the 18.5 my cruise speed came up like I was hoping. Now I am wondering if I should raise the motor 1 hole. Right now it is mounted one hole down from the top (next...
Forum: Recovered Threads 06-09-2016, 08:52 PM
Replies: 4
Views: 104
Posted By Captdj
I have a 2001 with a single tank doesn't say how...

I have a 2001 with a single tank doesn't say how many gallons. Paperwork says 135, but after a complete tank pump out we put more then 135 back in to fill it all the way up. 150 sounds right.
Forum: Recovered Threads 06-09-2016, 07:36 PM
Replies: 8
Views: 65
Posted By Captdj
I have bottom paint. I have two thru hull pick...

I have bottom paint. I have two thru hull pick ups. One starboard and one port. Port is livewell pick up and starboard is saltwater washdown. Have a thru hull ducer installed on the port side side...
Forum: Recovered Threads 06-08-2016, 10:23 PM
Replies: 8
Views: 65
Posted By Captdj
Looked today when I was down putting the 18.5 on...

Looked today when I was down putting the 18.5 on and the motor is mounted 2nd hole from the top. Motor is mounted straight to the transom no bracket, spacer, or JP
Forum: Recovered Threads 06-07-2016, 08:02 PM
Replies: 24
Views: 207
Posted By Captdj
I'll have to check what hole I am mounted in....

I'll have to check what hole I am mounted in. It's running great so not wanting to start messing around and going up and down holes.
Forum: Recovered Threads 06-07-2016, 08:00 PM
Replies: 8
Views: 65
Posted By Captdj
I'll have take a look tomorrow when I run down to...

I'll have take a look tomorrow when I run down to swap out props. You should be able to swing the 18.5 from everything I have ready most guys are running the 18.5. I was wondering if I could go up to...
Forum: Recovered Threads 05-31-2016, 11:21 AM
Replies: 8
Views: 65
Posted By Captdj
It is a 2001 CC

It is a 2001 CC
Forum: Recovered Threads 05-30-2016, 03:15 PM
Replies: 24
Views: 207
Posted By Captdj
I think I read right that you already had the...

I think I read right that you already had the repower done, but I just did the same thing. 2001 23 Seacraft with a 300 Suzuki 30 inch shaft mounted right on the transom. Love it do with I could get...
Forum: Recovered Threads 05-30-2016, 02:49 PM
Replies: 8
Views: 65
Posted By Captdj
Prop question

Have a 2001 23 SeaCraft and repowered with a 300 Suzuki (30 inch shaft no bracket) recently and looking to see if anyone has run the 16X20 with that set up?

I have asked and looked on other post...
Forum: Recovered Threads 10-30-2015, 08:36 PM
Replies: 4
Views: 90
Posted By Captdj
23 Seacraft with F300

I have a 2000 23 seacraft currently running a 300 HPDI. Either you love them or hate them, well I am starting to be in the hate them category. Can't seem to get it to run right enough to love it. So...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT -4. The time now is 11:41 PM.

Contact Us - Classic SeaCraft Home - Archive - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
All original content © 2003-2013 ClassicSeacraft