Classic SeaCraft Community  

Go Back   Classic SeaCraft Community > Recovered Threads
FAQ Community Calendar Today's Posts Search

Notices

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 09-06-2021, 10:23 AM
jorgeinmiami jorgeinmiami is offline
Senior Member
 
Join Date: May 2005
Location: Miami Fl
Posts: 1,613
Default Question on hydraulic steering

So Saturday when I went out I had a issue with my steering. It would work somewhat but it was soft and would not stay straight and if you would not constantly steer to the right but would go left. I bought some fluid and the hose and tried to bleed it out but with limited knowledge, tools and being in the water it stayed the same.

I did google some info the shows how to connect various hoses on a t connector it get the air out.
My question is the following.....is bleeding the air our fix the system or do I have a new or rebuild of the ram coming up?
Reply With Quote
  #2  
Old 09-06-2021, 07:06 PM
caper caper is offline
Senior Member
 
Join Date: Nov 2004
Location: Cape Cod
Posts: 258
Default

Bleeding is successful fix in most cases
Reply With Quote
  #3  
Old 09-06-2021, 08:12 PM
Capt Chuck's Avatar
Capt Chuck Capt Chuck is offline
gucci
 
Join Date: Aug 2003
Location: Sailfish Capital, fla
Posts: 2,804
Default

Quote:
Originally Posted by caper View Post
Bleeding is successful fix in most cases
It takes 2 people to properly bleed the air out of your hydraulic system.
One to add fluid at the helm & turn the wheel. The other to open & close the bleeder valves at the engine .
BTW: Have a shit load of rags on hand!
__________________


1978 23' Superfish/Potter Bracket 250HP --------



as "Americans" you have the right to ......
"LIFE, LIBERTY and the PURSUIT of a Classic SeaCraft" -capt_chuck
Reply With Quote
  #4  
Old 09-06-2021, 08:58 PM
bumpdraft bumpdraft is offline
Senior Member
 
Join Date: Apr 2012
Location: Sebastian,Fl.
Posts: 612
Default

I had a problem with air in the system and bled it. It worked fine for a while but started to get spongy and the fluid got low. I bought a seal kit for the ram. I inspected the shaft and didn’t see any obvious scratches or cracks. Upon further inspection,using my fingernail, I found a tiny, what appeared to be a crack. I cleaned the area well and then mixed up a small amount of jb weld marine. After putting a very small amount over the area and letting it cure, I carefully sanded it with something like 1000 grit paper. Installed the kit , bled the system again and that was a couple years ago. Still holding (knock on wood).
Reply With Quote
  #5  
Old 09-06-2021, 10:41 PM
jorgeinmiami jorgeinmiami is offline
Senior Member
 
Join Date: May 2005
Location: Miami Fl
Posts: 1,613
Default

https://www.thehulltruth.com/boating...-yourself.html

I'm going to try this this week
Reply With Quote
  #6  
Old 09-07-2021, 10:31 AM
jbass03 jbass03 is offline
Recovered
 
Join Date: Jul 2021
Posts: 4
Default

I used a system like this and it works great if you're solo and makes minimal mess. Looks easier than the hull truth method.

https://www.amazon.com/Timothy-Compa...24320371&psc=1

Here is a video explaining.
https://www.youtube.com/watch?v=0_EqQmSrHeQ
Reply With Quote
  #7  
Old 09-09-2021, 04:38 AM
strick strick is offline
Senior Member
 
Join Date: Aug 2003
Location: California
Posts: 2,738
Default

Easier with two people but I’ve done it alone by hanging the bottle over the helm...like capt chuck says have wraps handy...

Strick
__________________
"I always wanted to piss in the Rhine" (General George Patton upon entering Germany)
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:05 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
All original content © 2003-2013 ClassicSeacraft