Getting started

[TUGBOAT]

Let Me know where to send,It'll leave tomorrow.
All it takes is to : Back down Hard on chasing a Marlin;stern to anchoring?;Stopping real fast & letting the Wash get Ya;Following Sea ! Only one of these You'll appreciate That Xtra 5"s.SeaCrafts sit stearn heavy.Add 500#' & she's really low.I run a Merc.150 on My 20'MA had a 200 would'nt go over that.
Scream'n Reels' [img]images/icons/cool.gif[/img]

[ September 10, 2003, 10:21 PM: Message edited by: Capt. Brad ]

[and then some]

Do you think the extra five inches the motor is up would cause the boat to sit even lower in the water and cause more problems with the scuppers?

[TUGBOAT]

There are only a few things(Very Few & their outweighed by the Greats) anyone can say a bad thing about seacrafts.One of them is Drainage/Scuppers.You'll find all kinds of post on any fix,complaint,ideas etc.Take a Day to reveiw the archives.Thats what makes this site so "Great" is all the "ADVICE" .I just re-did mine ,just removed the ss scuppers & added the ball scuppers.She doesn't sit in the water,but on a trailer.Hope this helps Her.I always kept them plugged before.
Scream'n Reels'
Your sample is in the Mail/You have e-mail also
"TUG" [img]images/icons/cool.gif[/img]

[TUGBOAT]

Here is a couple of names of the Foam
Divicell/or Divycell - air rex its 24# not 40 as I thought.A company in Hialeah,Fl. has it.polyumac.Most shops in Your area should have or can get.
Scream'n Reels'
"TUG" [img]images/icons/cool.gif[/img]

[abl1111]

Welcome to the board. I am re-doing a SC23 Tsunami w/ a buddy who is a pro fiberglass guy. It seems that all the pros like to use plywood to rebuild with. Don't know why, but they all do. They figure - if it is built right and sealed right and maintained - then it will last forever. I tend to agree! I will however, be epoxying all thru-transom holes so the bitch will never rot again ! Can I get an Amen !

As for cutting the transom out. I did this myself and it is a 12-16 hour thing ( I had a bigger area to work on - i/o's ). I used a circular saw in some areas to make some 'entry cuts' and a sawzall w/ a wood blade to do a lot of cutting ( I used the sawzall to go through the wood and you can easily hear or feel when the blade cuts through the wood and taps the inside of the glass - then you stop!). The above tools just help make 'chinks' in the wood -then I used either a wonderbar, a few big screw drivers, and a new, sharp chisel/hammer to remove the wood. Some areas came off easy - in sections - others fought me the whole way. Some sections I was able to take off the (2) pcs of 3/4" ply and in others, on ply at a time.

Take your time. There is no easy way around this. It sucks and then your done! Until you have the next pain in the ass part to do. Do it systematically and ask A LOT of questions.

And in the end - you'll have an awesome boat !

Another tid bit: take it easy and make it an enjoyable project or it can really suck. Always have a cooler of cold beer around - it is great when you bash your hand, cut yourself or are plain ole' freak'n tired !

Good luck !

Alan

[FELLOW-SHIP]

HA ABLE1111
I totally agree with your last statement my boat took a little over a year to complete and now looking back when I started putting time stipulations on my self and when I ran out of beer is when it stopped being fun. If I had to do it all over again I would think 30% more time and 50% more beer would be just about right.
FellowShip [img]images/icons/smile.gif[/img]

[TUGBOAT]

I'm gonna ASSume that the other 20% would to be spent with The Wife / Family So You COULD do it AGAIN !!
Scream'n Reels' [img]images/icons/cool.gif[/img]