Trim tab supplier

bigeasy1 · #1 09-11-2007, 09:49 AM

I need to order a set of Bennett tabs for my Tsunami,and am looking for the best place to get them for the best price.They are 12x12 with a 3"drop fin on each edge.
The problem is,is that nobody stocks that tab,they have to be special ordered.I tried some of the smaller independent suppliers,but most either never got back to me,or didn't want to do special order.

Of course the big box bandits like worst marine, will special order them,but they want the full factory list price of $703.00.
I bought tabs in the past,and don't mind paying a fair price,but no one sells anything for the factory list price.

I would also much rather give my business to a small independent guy than some giant big box company.
If anyone can recommend a good source,it would be appreciated.Thanks all.

toddslures · #2 09-11-2007, 10:22 AM

I assume you are after the M-120 kit. I will get you a price on it. E-mail me your shipping address to.

NoBones · #3 09-11-2007, 10:26 AM

Shoot Tabman (a member of this site) a PM
He works at Bennett. He will direct you to the best place.
Bennett donated two sets of tabs for our Anclote gathering this past April of which we raffled off.
They are a great company!!!
See ya, Ken

bigeasy1 · #4 09-11-2007, 10:46 AM

Todd,The part # is 1212DFE. these were the tabs recommended by Bennett in my phone conversations with them.
It'a a 12x12 tab with a 3"drop on each side.
I beleive that they are a bigger drop and a heavier tab than the M120's.
Bennett told me that they give a much better lift than the standard tabs.

Tarpinmon · #5 09-11-2007, 11:01 AM

Since were talking about trim tabs what the thoughts on Lenco vs Bennett. Two complete different designs. Is it just 6 of one half dozen of another? Looking to equip a 20'

toddslures · #6 09-11-2007, 11:14 AM

John,
12X12DF with the LS3000 waterproof rocker control, $600 including shipping to you.

hermco · #7 09-11-2007, 06:35 PM

I use the Lenco tabs. No pump or fluid to deal with, waterproof switch and they are right down the street from me.

NoBones · #8 09-11-2007, 08:00 PM

Quote:

Since were talking about trim tabs what the thoughts on Lenco vs Bennett. Two complete different designs. Is it just 6 of one half dozen of another? Looking to equip a 20'

Well, my 20SF has 9 x 24 Bennett's that are 30 + years old
never replaced a thing, my flats boat has 9 x 12 Bennett's that are 21+ years old with no problem other than one of the tab indicators that went bad and Bennett made it very affordable to replace. You be the judge. Properly installed
the Bennett's (I Believe) will live longer then you......
see ya, Ken

hermco · #9 09-11-2007, 08:13 PM

You must have got the ones made for the owner. I have replaced hundreds of HPU's and switches in the past 20 years.

NoBones · #10 09-11-2007, 10:05 PM

Quote:

You must have got the ones made for the owner. I have replaced hundreds of HPU's and switches in the past 20 years.

My HPU is mounted in a very dry area in the transom locker. The racing style switch is the most bullet proof one made. Which is the one I used on both boats.
A joy stick on anything just won't last........
Again if installed properly it will be trouble free,
and yes both of my boats are used alot. They do not just sit in the barn to look at.

If you want real hard core tabs go to K planes.
Everyone has there opinion on what works best for them.
Just my 2 cents worth. For me it will always be Bennett !!
See ya, Ken