floor repairs

[Blue197320]

hey
i looked in my photobucket for pics of that floor repair. im sorry i dont have any. but i can tell u that it only took me about 2 days after work to do it start to finish. the piece i cut out was a funny shape so i took a few pieces of plywood and puzzed it together on top of the wet cloth i put down. then i poured resin in to fill the gaps around the puzzle pieces. then i put a few more layers of cloth on top of the wet resin and let it soak the resin up. it was close to the original height so i didnt need to add much filler. then i sanded and primed it. i still need to paint the whole floor in my boat but its gonna need to to be ripped up in a year or two so im not going to finish it yet. but u can do it. trust me. anything else just ask.

[bigeasy1]

I had a couple soft spots in the deck of my Tsunami under the pedestall seats.I had to recore them,and it's a fairly easy fix.

I cut the top layer of glass off,using a circular saw,set to about a 1/4"depth.
I then removed the piece of deck,which in my case was about 24 x 36 inches on each area.That now exposed the core,which was plywood directly where the seats mounted,and balsa core on the rest.

Again with the saw set to a shallow depth,i cut thru the core,(it was 3/8"),just to but not thru the bottom piece of glass.
I chiseled,scraped,and ground out the wet rotted core until i hit dry material.

After i prepped the bottom layer of glass,i laid up a piece of 1-1/2oz mat to it,and let it kick a bit,then took some 3/8" marine plywood,and bedded that into the mat,by applying a slightly thinned hull and deck putty to the faces of the mat and plywood.

I placed a whole bunch of 12lb downrigger weights on the plywood until the resin/putty cured.
When it was done i laid up a layer of mat on top of the repair.

At this point,i think i'm going to put a layer of mat over the whole deck,and mask off sections leaving a white border with areas of gray or tan non skid.

The bottom layer of glass was extremely thin and several holes where the seat bolts were drilled,went thru the glass into the stringer boxes.Also i found vacant holes drilled into the boxes,(maybe for the foam filler)and i think thats where some of the water saturated foam in my stringers came from.

Maybe these pictures will help.
The first one is after i had already cleaned up the area and put down a layer of mat,and the last is one layer of mat over the repair

[beradtke]

that you both for the advice i am going to start buying the supplies to tackle this job. my other question is did either of yall match what the original floor looked like with the grooves running in it. if so how did you do that????

[bigeasy1]

I thought about matching the original deck floor,but decided against it.
I guess it could be done but it's way way more tedious work then i'm interested in doing.
My use for this boat is strictly fishing,i want it to look nice when it's done,but i'm not interested in having it be the equivilent of a concours classic car.
As i said in my post,i'm going to lay up mat on the whole deck,and mask off areas and do them in a gray or tan non skid,with a white border edge.

[Billybob]

If you want to match the original pattern, go to an auto body supply place with the width, I forget what it is, but it's a little off standard. Get the blue plastic tape, spray the whole floor first, then lay you're masking and roll/spray your non-skid. I think that's a detail that looks great, especially if you go a little darker with the non-skid, like a tan.

[Blue197320]

my floor did not have those lines. i had non skid on it. i have not put non skid on the area again. i did mine exactly the same way as those pictures describe.

[beradtke]

sorry about the slow replie been busy. goor to looking and i thought the raised section of the floor was engrained in the floor. i didnt know it was just non skip with sections missing where there was tape at. now i know i can match it i am quite please. has any one ever filled the floor area completely with glass resin,instead of putting wood down i am just curious??