Classic SeaCraft Community  

Go Back   Classic SeaCraft Community > General Discussion > Repairs/Mods.
FAQ Community Calendar Today's Posts Search

Notices

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 10-25-2011, 09:31 AM
Handful in NC Handful in NC is offline
Senior Member
 
Join Date: Jan 2010
Location: New Bern, NC
Posts: 119
Default

Oops. Trim tab issues. Lenco edge mount 12X12 tabs won't work without cutting holes in the bracket (though Capt Chuck did this on his 23' with good results). A 9" wide tab would allow the cylinder to fit outside of the bracket, but it still is quite high.





Solution: QL tabs. I'd never heard of these. Volvo Penta has a history of pushing the design envelope and these certainly are different. They basically have a blade that drops straight down and creates a hydraulic wedge. Installation is a challenge as they must mount to a perfectly flat surface so the housing isn't distorted, which jams the blade. (Yes, been there, done that.) One nice thing, the thin profile makes them impossible to smash at the dock. They are a perfect fit and work really well.

Reply With Quote
  #2  
Old 10-31-2011, 04:09 PM
Handful in NC Handful in NC is offline
Senior Member
 
Join Date: Jan 2010
Location: New Bern, NC
Posts: 119
Default

The boat was launched 10 days ago. A close friend was along to keep me from doing anything particularly stupid on the inaugural launch. All went well and, thankfully, concerns about the cabin weight in the front were not justified. It sits in the water nicely. The cockpit does drain aft. I briefly opened up the new motor and saw 48 mph. Cruise numbers are approximately 30 mph at 3000 rpm and 3 mpg. (Amazingly, my old 21' Parker with a 175 Johnson 2 stroke at the same speed/rpm got half that mpg!) More detailed performance numbers will follow, but that 250 Etec is pretty sweet thus far.

My schedule and the weather have not cooperated for getting good photos to post, so I've been working on the aft cabin bulkhead/doors, using 1/2" starboard with acrylic windows to keep the weight down. (Don't want to push my luck on the forward weight issue.) We had our first cold snap this past weekend, so that enclosed cabin with a little duck blind heater is going to be really nice for winter boating.




Reply With Quote
  #3  
Old 10-31-2011, 04:20 PM
DonV DonV is offline
Senior Member
 
Join Date: Jul 2004
Location: Apollo Beach or Islamorada
Posts: 3,488
Send a message via ICQ to DonV
Default

Damn Bill!!!! Beyond sweet!! Congrats.
Reply With Quote
  #4  
Old 10-31-2011, 08:49 PM
Blue_Heron Blue_Heron is offline
Senior Member
 
Join Date: Jan 2006
Location: Gator Country
Posts: 1,416
Default

Very nice. Thanks for posting the links on the headliner. I'm in the same boat as strick so to speak. What is the exterior finish on the boat/pilothouse? What color? Looks very good with the teak.
Dave
__________________
Blue Heron Boat Works
Reinventing the wheel, one spoke at a time.
Reply With Quote
  #5  
Old 10-31-2011, 09:33 PM
Blackfin26 Blackfin26 is offline
Senior Member
 
Join Date: Feb 2008
Location: Brewster, MA
Posts: 396
Default

Super nice....should be mass produced. Thanks for sharing.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:17 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
All original content © 2003-2013 ClassicSeacraft