Internal mixing resin spray gun

[Basketcase]

I get it. I too am used to the old school way. The theory is that it mixes in the air. To me that seems odd but it must work. The flow of mekp is adjustable and id guess that it takes some experimenting to get it right. You have to admit the idea is tempting. Readily mixed. Zero waste. No buckets. It's the same as the guns that spray glass from a chopper gun and also spray resin. I think they use those for bathtubs and such. Since I don't use a lot of chopped strands I don't need that but I've always been intrigued by a mixing gun.

[Bigshrimpin]

for $1000 you could buy a used venus chopper gun and a few pails for resin.

[flyingfrizzle]

By buddy has a chopper gun and was building Carolina skiff copies and was using clear mekp. Big mistake. One time he stopped up the gun or line to the mekp and sprayed half of a mold with out the mekp flowing and only half of the hull layup hardened. Big big mess. Then he went to red die mekp to ensure the mix was happening. Finally he sold the whole set up, and told me it was more trouble than it was worth. Clean up was a bit*$ and it was only good for spraying large molds (full hulls basically).

Me, I want to mix mine at the rate I want in batches. Throw away the mess hardly no clean up. If I for get to clean the roller...the bottle torch will fix that quickly.

If you did several full hull molds a week maybe but to do small jobs, I like to do it by hand.

[kmoose]

Originally Posted by flyingfrizzle

By buddy has a chopper gun and was building Carolina skiff copies and was using clear mek. Big mistake. One time he stopped up the gun or line to the mekp and sprayed half of a mold with out the mekp flowing and only half of the hull layup hardened. Big big mess. Then he went to red die mekp to ensure the mix was happening. Finally he sold the whole set up, and told me it was more trouble than it was worth. Clean up was a bit*$ and it was only good for spraying large molds (full hulls basically).

Me, I want to mix mine at the rate I want in batches. Throw away the mess hardly no clean up. If I for get to clean the roller...the bottle torch will fix that quickly.

If you did several full hull molds a week maybe but to do small jobs, I like to do it by hand.

I'm with you on the dyed MEKp and got to where I could gauge the ratio by the color when mixing by hand. Many would be amazed on how well resin and mekp needs to mixed until you use the dyed stuff. It solves a lot of problems. Too bad you can't use it with gelcoat.

[gofastsandman]

Originally Posted by kmoose

I'm with you on the dyed MEK and got to where I could gauge the ratio by the color when mixing by hand. Many would be amazed on how well resin and mek needs to mixed until you use the dyed stuff. It solves a lot of problems. Too bad you can't use it with gelcoat.

I`m a good mixer. Small batches are good for one ciggie.
Never knew there was colored mekp. So does this cure a darker color of red than
regular mek?

[hermco]

Originally Posted by gofastsandman

I`m a good mixer. Small batches are good for one ciggie.
Never knew there was colored mekp. So does this cure a darker color of red than
regular mek?

[flyingfrizzle]

Originally Posted by pelican

i'm confused
big difference between these 2 products...

If you don't "p" in it, it don't work. Drink lots of water before adding the p so the gel coat don't turn yellow....

[Basketcase]

Originally Posted by flyingfrizzle

By buddy has a chopper gun and was building Carolina skiff copies and was using clear mekp. Big mistake. One time he stopped up the gun or line to the mekp and sprayed half of a mold with out the mekp flowing and only half of the hull layup hardened. Big big mess. Then he went to red die mekp to ensure the mix was happening. Finally he sold the whole set up, and told me it was more trouble than it was worth. Clean up was a bit*$ and it was only good for spraying large molds (full hulls basically).

Me, I want to mix mine at the rate I want in batches. Throw away the mess hardly no clean up. If I for get to clean the roller...the bottle torch will fix that quickly.

If you did several full hull molds a week maybe but to do small jobs, I like to do it by hand.

I wonder if your buddy's setup was a pain because of the chopper gun? I wonder if just a mixing gun would be less of a problem.

I'm fairly certain the reason the red mekp was made is for these systems. I've used it before and it does help to let you know when you mixed enough. I really want to try one of these guns, but $1k is not an amount of money I want to experiment with. If it will make life easier and add value to my projects, I'm all for it, but so far I haven't gotten a warm fuzzy feeling!