Forum: Performance
05-12-2009, 11:16 PM
|
|
Replies: 33
Views: 911
Re: motor weights, too much?
150 will be great on the boat, you'll love the power.
I realized an error in my numbers, that was about 18nm, not miles or about 20 statute miles, so about 4mpg...
Have fun with the new engine!
|
|
Forum: Performance
05-11-2009, 04:12 AM
|
|
Replies: 33
Views: 911
Re: motor weights, too much?
I had a Yammy 175 carbed two stroke, it was about 420 lbs or so and I thought that was too much weight on my 20CC. I repowered with a Etec 115. Weight is good, no water comming in the scuppers.
...
|
|
Forum: Repairs/Mods.
06-04-2008, 03:05 PM
|
|
Replies: 12
Views: 390
Re: Transducer placement location 20cc?
I didn't cut my cable. When it was on the transom I ran it through the wiring duct from the console to the transome bilge then ran the wire out the engine cable exit and over the transom. (Actually...
|
|
Forum: For Sale
06-04-2008, 02:16 AM
|
|
Replies: 12
Views: 182
|
|
Forum: Repairs/Mods.
06-04-2008, 01:07 AM
|
|
Replies: 12
Views: 390
Re: Transducer placement location 20cc?
Interesting, I tried mine there and changed the heights and tried it outboard from there about 3" in from the next chine but just couldn't stop the bubbles from interfering at anything above 1200 rpm...
|
|
Forum: General
06-03-2008, 04:47 AM
|
|
Replies: 3
Views: 145
Re: engine weight
My 2008 Etec 115 weighs about 375. I added a leg extension kit to a 20" to make it 25". I heard they are comming out with a 130.. probably the same weight and block etc..
|
|
Forum: Repairs/Mods.
06-03-2008, 04:31 AM
|
|
Replies: 12
Views: 390
Re: Transducer placement location 20cc?
These pictures are not the greatest, I had to take them at night with the flash so it was hard to get a good shot. I might be able to take some before work tomorrow.
Here is the water tight...
|
|
Forum: General
06-02-2008, 03:01 AM
|
|
Replies: 7
Views: 221
Re: Antenna vs. Bimini?
I have a 20 CC with a bimini. I mounted my antena on the starbord rear corner of the boat, about 6" forward of where the transom boxes come accross, about 1 1/2 foot in from of the transon. Mine is...
|
|
Forum: General
06-02-2008, 02:41 AM
|
|
Replies: 3
Views: 194
Re: Weight of SC 20 all up???
I have a 20cc, 115hp E-tec, dual axle trailer and pull it with my Saturn Vue.. 6Cyl AWD.. works fine though I would not want to pull anything bigger..
Aloha..
|
|
Forum: Repairs/Mods.
06-01-2008, 10:41 PM
|
|
Replies: 12
Views: 390
Re: Transducer placement location 20cc?
Thanks Loyd...
I spent the day remounting it, tried to mount in the aft bilge under the false transom but it is so difficult to work in with only the small round screw plate in the stern/engine...
|
|
Forum: Repairs/Mods.
06-01-2008, 05:13 PM
|
|
Replies: 12
Views: 390
Transducer placement location 20cc?
Where does everyone mount their transducers? I have tried a few places on the transom making sure it was properly inline with the bottom of the boat to reduce bubbles. When I get above about 1200...
|
|
Forum: Performance
03-07-2008, 08:07 AM
|
|
Replies: 6
Views: 258
Re: Another Prop ?
I have a 115 E-tec running a 15p on my 20 CC, seems just about right for my boat. I also think the 17p will be a good fit for your boat with the 150hp.
|
|
Forum: Performance
03-07-2008, 08:01 AM
|
|
Replies: 25
Views: 563
Re: 20 Master Angler 115 ETEC v. 150 ETEC
Grady,
Did you get your 150? So far I am really happy with the performance of the 115. I had 4 people in the boat and really couldn't tell much difference from when it was just me alone. I also...
|
|
Forum: Performance
02-14-2008, 07:52 AM
|
|
Replies: 25
Views: 563
Re: 20 Master Angler 115 ETEC v. 150 ETEC
I just put an Etec 115 on my 20ft SF. I haven't had time to really use it yet but it runs fine, plenty of get up and go. (I used to have a Yamaha 175 on it..) I like the lighter weight as the SF...
|
|
Forum: Performance
02-14-2008, 07:42 AM
|
|
Replies: 11
Views: 344
Re: Etec 115 hp shaft extention question
Late update, I got the extension kit installed. It wasn't too hard but there were some tricky parts to it. I made a document with photos of the process incase anyone else needs some guidance as the...
|
|
Forum: Repairs/Mods.
11-25-2007, 06:31 AM
|
|
Replies: 7
Views: 327
Re: yamaha F150 and a 20' seacraft
I had a carbed 6 cyl Yamaha 175, weighed about 419lbs on my 20 with a 25" transom. The boat ran great with it though the engine may have been a little heavy when stopped. Two people in the stern and...
|
|
Forum: Repairs/Mods.
11-17-2007, 07:26 AM
|
|
Replies: 12
Views: 475
Re: SF20 gas tank dimensions
Muddywater,
My tank is 7' 10" long and 22" wide, not sure of the depth as it is foamed in. I'd guess about 10" or more in the middle. I think it holds about 75 gallons.
|
|
Forum: Performance
11-17-2007, 07:14 AM
|
|
Replies: 11
Views: 344
Re: Etec 115 hp shaft extention question
Kamikaze,
I have no problems dropping the lower unit and changing water pumps etc.. What do you use to ream out the midsection so that the shaft extension will fit through? It may become obvious...
|
|
Forum: Repairs/Mods.
11-16-2007, 10:26 AM
|
|
Replies: 12
Views: 475
Re: SF20 gas tank dimensions
What size tank are you looking for? I have a 75gal tank in mine. The specs for this boat on this site say 47 gal is standard. My tank is about 6 feet long and one inch too wide (can't get it out of...
|
|
Forum: Performance
11-16-2007, 04:55 AM
|
|
Replies: 5
Views: 184
Re: Prop Size for 115 hp on 20 CC
skippertee and all, thanks for the responses. I ordered a viper 14x15" prop. I'll post later when I get the boat running how it performs, may be a while though.
|
|
Forum: Performance
11-16-2007, 04:53 AM
|
|
Replies: 11
Views: 344
Re: Etec 115 hp shaft extention question
Thanks all for your responses. The dealer is shipping a Bay Extension kit. When it comes I guess I will need to find an official "dealer" to install it to maintain the warranty from Bay. I spoke...
|
|
Forum: Repairs/Mods.
11-09-2007, 03:59 AM
|
|
Replies: 1
Views: 299
How to remove fuel tank from a sf20?
I have my boat apart and want to check the 75Gal fuel tank in my sf20. It appears the opening is about 1 inch too narrow to lift the tank out. (Why would someone design such a thing?). Is foamed...
|
|
Forum: Repairs/Mods.
11-09-2007, 03:47 AM
|
|
Replies: 1
Views: 271
Re: Fixing gelcoat on non-skid areas
I have never tried this with gel coat but don't see why it would not work. I used to build windsurfer's and put non-skid on the decks by laying down a thin coat of finishing resin and then using a...
|
|
Forum: Repairs/Mods.
11-07-2007, 08:55 PM
|
|
Replies: 0
Views: 309
Engine extension kits - Bay Manufacturing
Has anyone installed a Bay Manufacturing extension? I will need to install one on my new Etec 115 (don't ask why, ughh!) Was it diffucult? Any issues? Are they reliable?
Thanks
|
|
Forum: Performance
11-06-2007, 02:55 PM
|
|
Replies: 11
Views: 344
Etec 115 hp shaft extention question
Etec 115 HP:
The dealer shipped a 20" instead of the 25" and won't pay for the double shipping to return the engine and ship the one that I ordered. So, I have to install an extention. The 20"...
|
