Forum: General
08-09-2003, 10:12 PM
|
|
Replies: 3
Views: 85
Re: Who has a 20 I/O?
I recently replaced my volvo with the 3 liter I/O Merc on my 20fter. I usually cruise at 3300-3500rpm = 23knots. 4000 rpm = 26knots. At 4800rpm =32knots.
|
|
Forum: Repairs/Mods.
04-17-2003, 08:52 PM
|
|
Replies: 3
Views: 116
Covers for the rod holders
Owning a 20' I/O, I'm very cautious about getting water in the bilge. I've had trouble with splashing water and my starter. I've gone to one of those new electronic sensor bilge pumps that works...
|
|
Forum: General
03-23-2003, 10:24 PM
|
|
Replies: 859
Views: 69,892
|
|
Forum: General
03-19-2003, 09:52 PM
|
|
Replies: 34
Views: 251
|
|
Forum: Repairs/Mods.
03-16-2003, 08:25 AM
|
|
Replies: 13
Views: 217
Re: Leaking floor scuppers
Can anyone post a picture of these wedges before the scuppers. I like to check out what they look like in the way of size, shape and how far in front of the whole to put them. Thanks!
|
|
Forum: General
02-27-2003, 05:09 PM
|
|
Replies: 2
Views: 71
IS IT 19.5 OR 20.5
MY BROTHER HAS JUST PURCHASED A SEACRAFT CC BUILT IN 1975 THAT HAS BEEN TOTALLY REDONE. THERE ARE NO MARKINGS ON THE HULL AND THE TITLE HAS NOT BEEN TRANSFERRED. WHAT A GEORGEOUS RIG! THE OWNER CALLS...
|
|
Forum: Repairs/Mods.
02-26-2003, 04:55 PM
|
|
Replies: 13
Views: 217
|
|
Forum: General
02-26-2003, 04:53 PM
|
|
Replies: 8
Views: 125
Re: "74, 20' cc I/O Merc or Volvo
Jon G, Thanks for the note. I bought the last block from them. This time I'm going with the Merc. Hope is will handle the ocean better.
|
|
Forum: General
02-26-2003, 09:11 AM
|
|
Replies: 8
Views: 125
Re: "74, 20' cc I/O Merc or Volvo
When I bought the boat a few years ago it was refit with a new 4 cyl volvo. Had no problems with the drive, tons of trouble with the engine (pumps, starters, drive cones, rust, flappers,carb trouble,...
|
|
Forum: Repairs/Mods.
02-26-2003, 09:04 AM
|
|
Replies: 13
Views: 217
Re: Leaking floor scuppers
Looking carefully at the brass it does not look to be lower than the bottom of the hull. There is no dam. What would you recommend? Is it hard to replace the brass tubes? Thanks
|
|
Forum: General
02-25-2003, 07:42 PM
|
|
Replies: 8
Views: 125
|
|
Forum: Repairs/Mods.
02-25-2003, 07:38 PM
|
|
Replies: 13
Views: 217
Leaking floor scuppers
Own a "74 CC I/O that has leaking floor scuppers into the bilge. Whats the best way to stop the drip? Also, any idea why one of the floor scuppers sucks the water out of the boat and the other one...
|
