Classic SeaCraft Community  

Go Back   Classic SeaCraft Community > General Discussion > Repairs/Mods.
Reload this Page A little lot of Karma. or re birth of a 20
FAQ Community Calendar Today's Posts Search

Notices

Reply
Page 6 of 8 « First 45 6 78
 
Thread Tools Search this Thread Display Modes
  #51  
Old 02-18-2012, 05:22 PM
Joe R Joe R is offline
Senior Member
  
Join Date: Jun 2003
Location: Smithville NJ
Posts: 390
Default
Hope Carmen brings it to our Atlantic City get together this summer,,,
Hay Hay,,, Bruce,,,how bout having it in Ventnor LOL...I know someone with a house on the water there LOL...

Joe R.
20ft Classic SeaCraft
Susie II
__________________
Joe R
Reply With Quote
  #52  
Old 02-18-2012, 05:23 PM
GCC GCC is offline
Junior Member
  
Join Date: May 2011
Posts: 3
Default
Quote:
Originally Posted by workinpr0gress View Post
Looking great Bly, "Lefty Bly Edition", lol.

GCC nice to see ya on here, that homebuilt you're doing is coming along Great!
Thx man. I plan to have the deck in, in the next few days weather permitted. Ive been lurking around this site and classic mako for several years, just dont usually post......Lots of great info and craftsmanship on both sites.
Reply With Quote
  #53  
Old 02-18-2012, 06:52 PM
workinpr0gress workinpr0gress is offline
Senior Member
  
Join Date: Jun 2009
Posts: 601
Default
Quote:
Originally Posted by Joe R View Post
Hope Carmen brings it to our Atlantic City get together this summer,,,
Hay Hay,,, Bruce,,,how bout having it in Ventnor LOL...I know someone with a house on the water there LOL...

Joe R.
20ft Classic SeaCraft
Susie II
That boat might be too pretty for our get together, lol.
We could do that, just gotta kick the renters out, lol. I'll be back from Jamaica by then.
__________________
Thank goodness that in the scheme of things you are broke, powerlesss and inconsequential, because with the shortsighted alternatives and idealogy you have you'd be much worse than those you complain about.
Reply With Quote
  #54  
Old 02-29-2012, 09:55 PM
bly bly is offline
Member
  
Join Date: Oct 2011
Posts: 82
Default I am finally putting the floors down for good.
The back one is glassed down permanently. The next one will be down for good tomorrow. I was waiting on the gas lines which arrived at my door today. I love ebay. and UPS. then maybe the third this week end.









room for a couple 60 inch blue fins under the deck.



It sure seems like a big 20? I guess making a three piece boat is a big difference.Oh one or two more. I went a little anal on the helm pod.




No varnish either.
Reply With Quote
  #55  
Old 02-29-2012, 10:28 PM
gofastsandman gofastsandman is offline
Senior Member
  
Join Date: Mar 2007
Location: W.P.B. ,Fl.
Posts: 4,586
Default
You turn the grain nicely.
Cheers,
Us
Reply With Quote
  #56  
Old 02-29-2012, 11:18 PM
YeA 20sF YeA 20sF is offline
Senior Member
  
Join Date: Aug 2011
Location: S.FLA
Posts: 340
Default
wow cant wait to see this finished. I really like the single level deck on the 20 I could definatly see the advantages
__________________
78' / 20SF / Merc XRi Black Max 150
Reply With Quote
  #57  
Old 03-02-2012, 09:23 PM
bly bly is offline
Member
  
Join Date: Oct 2011
Posts: 82
Default I have pictures of the way aluminum fuel tanks are recommended
to be installed By S&P tanks. One of the bigger longer lasting companies still around. No foam around tank. It is bolted to the main stringers and sets on Neoprene pads installed under tank. If any water does get near tank it can drain away because of many openings or holes drilled in the fuel tank pad it sets on. Also all hoses have chafe protection . The grounds and fuel gauge wiring is done with shrink wrap connectors. I also tie off the wires with a loop and ties to Make sure No one can pull the crimped connectors a part.






I also glassed under
the penske boards the old fashioned anti gravity way. On horses up side down.

Reply With Quote
  #58  
Old 03-02-2012, 10:00 PM
NoBones NoBones is offline
Pooh Bah
  
Join Date: Apr 2004
Location: Area 442 Somewhere in Florida
Posts: 3,699
Default
Lookin' real good Bly!!!
Nice to see a little Southern in a Northern boat..
Also, one suggestion. Double opposing stainless clamps
on your vent and fuel lines. I learned the hard way!
__________________
See ya, Ken ©
Reply With Quote
  #59  
Old 03-02-2012, 10:35 PM
bly bly is offline
Member
  
Join Date: Oct 2011
Posts: 82
Default You actually had a clamp break nor come loose? I was just telling carmen how in 50
Quote:
Originally Posted by NoBones View Post
Lookin' real good Bly!!!
Nice to see a little Southern in a Northern boat..
Also, one suggestion. Double opposing stainless clamps
on your vent and fuel lines. I learned the hard way!
some years of boating and retiring as a pipe fitter working with hose clamps many times? If using a quality clamp I have never seen one fail. There have been many clamps I would not use tho. Then the other thing is on the fuel line pick up fitting? It was a actual Mueler fuel fitting I bought and not a plumbing fitting? So dont blame me. There is not room for two clamps unless I buy those thin clamps. A beefy clamp like I like will clamp mostly on bare hose and not the barbed fitting? I do not think that is good? Maybe since you proved My urban legend wrong I will atleast double the fill and vent hose. There is plenty of room on Those. I am not doubting you? I just thought if I have not ever seen one fail it must be one of those urban legends? Like not putting a battery on a cold concrete floor? That was when batteries were made with glass?
Reply With Quote
  #60  
Old 03-04-2012, 10:03 PM
NoBones NoBones is offline
Pooh Bah
  
Join Date: Apr 2004
Location: Area 442 Somewhere in Florida
Posts: 3,699
Default
Well I hear ya' bly....

I have always used nothing but the best around in hardware
and materials, when doing a boat.. (not just SeaCrafts)
I had a 308 stainless clamp that the worm screw just fell out!
It had not been over tightened if that is what you are guessing..
Luckily it was on an exposed fuel line on a 15 Whaler I had previously
owned! A friend in the marine business recommended double clamps,
keep in mind this was over 30 years ago with that tip.
I have adhered to that standard ever since..
Everyone has their way, this is just mine!
__________________
See ya, Ken ©
Reply With Quote
Reply
Page 6 of 8 « First 45 6 78

« Previous Thread | Next Thread »

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 09:41 AM.

Contact Us - Classic SeaCraft Home - Archive - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
All original content © 2003-2013 ClassicSeacraft